|
Everything on the car is in working condition and is a 8.5 out of 10 or better. This deuce has won its fair share
of awards including Best Chevy and Best 60’s Modified but don't let looks fool you, this is a drivers car not a
trailer queen. This Nova has a fun combination of old school mixed with new school. Expect looks and comments at
stop lights when you're behind the wheel. To the best of my knowledge this Pro Touring Nova was built in 2008 and
was painted as currently shown in late 2011. The motor, exhaust and rear end were installed in June of 2014. Fully forged Roller 4 bolt main small block with an estimated 500 HP/TRQ, professionally built by L&R Engines in
Santa Fe Springs, CA
Mid length 3/8” flanged ceramic coated Rewarder headers with dual 2.5” mandrel bent aluminized exhaust into
Stainless steel Magna Flow mufflers dumped before the rear axle.
Blue printed and balanced 350 Chevy Pre 79 4 bolt main bored 30 over. Inside blasted & epoxy coated.
Air Flow Research (AFR) Eliminator 65cc / 195 CFM aluminum heads with CNC porting.
3.75 Scat forged 4340 crank and 5.7” Scat Pro Comp forged rods
Probe Sportsman race series SRS forged pistons
Engine Pro 1.5 ratio Aluminum roller rockers
Compression 10.4:1
Isky roller cam .530/ .550 lift. 234/246 duration @ 050. 110 lobe.
Hydraulic roller lifters with link bars.
Holley 750 model 3130 double pumper built by C & J in Stanton. Carb flows 800 cfm and sits on top of a 3/8” wood
carb spacer.
Edlebrock RPM air gap manifold powder coated black.
Edlebrock 110gpm mechanical fuel pump.
MSD 85551 billet distributor curved by C & J w/ 18 base and 36 total at 3, 000RMP
Blaster 2 coil, 6AL soft rev ignition box and Black 8.5 MSD wires
Milodon baffled 5 quart plus filter pan
Polished billet Serpentine drive system with polished AC compressor.
3 core aluminum radiation with 180 thermostat and billet reservoir with electric Spal high performance puller fan
and thermostat control and manual override.
Fire wall has been smoothed and painted in a single stage black, AC/heater lines run through the fender and enter
the cab between the inner and outer fender.
All wires have been hidden including relocating the coil and 6AL box behind the center console.
Billet valve covers and air cleaner assembly.
2015 Red Top Optima battery located in trunk with kill switch and billet battery holder
Chrome stock hood hinges
New Lokar billet throttle cable/mount, billet trans and oil dipsticks.
Drivetrain & Brakes:
Turbo 400 with shift kit
18” finned aluminum transmission cooler
Built 58” wide Ford 9 inch with Currie housing and 3.08 gears with an Eaton posi
Custom built drive shaft.
Moser 31 spline axles
Nitto INVO Tires with 225/40/zr18 fronts and 255/40/zr18 rears (Tires have 75% tread)
18” wheels. One off NewGen Splitters. Front – 18x7’s w/4.5” backspace. Rear - 18x8’s w/5.5” backspace
Corvette dual master cylinder
Wilwood 13” drilled and slotted rotors with 4 piston calipers up front and 12” disks and 2 piston calipers in
the back.
Chassis Works proportioning valve for rear brakes
Car stops on a dime without power assist. Car only weighs 3100lbs.
Suspension & Chassis:
Complete Chassis Works mustang front clip with fender panels and billet motor mounts.
With 4 way individually adjustable shocks this car handles like it is on rails and can ride as stiff or soft you
like.
¾” front anti roll/sway bar
Polished Manual rack and pinion with Chassis works steering shaft and knuckles.
Air Ride 4 link Rear Suspension.
Air Ride Technologies suspension with digital 4 way ride control with 2 compressors and a 3 gallon tank. Mounted
between the rear seats and subwoofer.
Vari shock adjustable air ride bags/shocks
All four corner were revalved/rebuilt in 2014
Ride height is complete adjustable at all 4 corners individually. You choose the ride height you want plus clearing
odd drive ways/approaches is a breeze with this Nova.
Subframe connectors.
Interior:
Black Ultra Leather with grey and red inserts.
Eddie motorsports billet door pulls and window cranks arms. Billet rear view mirror
Custom center console running front to back with drink holder, arm rest and center console for storage
B&M hammer shifter with ratcheting action.
Custom 1 piece headliner done in leather with inserts.
10K spent on the interior and trun
|
